View SQE48T30033-NDC0_7669275.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 1 of 33 the new high temperature 30a semiq? family of dc/dc converters provides a high effi ciency single output in a size that is only 60% of industry-s tandard quarter bricks. specifi- cally designed for operation in systems that have limited air- flow and increased ambient temperatures, the sqe48t con- verters also preserve the same pinout and functionality of the industry-standar d quarter bricks. the 30a sqe48 series converters of the semiq? family provide thermal performance in high temperature environ- ments that exceeds most competitors' 30a quarter bricks. this is accomplished through the use of patent pending cir- cuits, packaging and processing techniques to achieve ultra- high efficiency, excellent thermal management and a very low body profile. low body profile and the preclusion of heatsinks minimize airflow shadowing, thus enhancing cooling for downstream devices. the use of 100% automation for assembly, coupled with di/dt?s advanced electroni c circuits and thermal design, results in a product with extremely high reliability. operating from a 36-75v input, the 30a sqe48 series con- verters provide any standard output voltage from 3.3v down to 1.2v. outputs can be trimmed from ?20% to +10% of the nominal output voltage ( 10% for output voltage 1.2v), thus providing outstanding design flexibility. with standard pinout and trim equations, the sqe48 series converters are perfect drop-in replacements for existing 30a quarter brick designs. inclusion of this converter in new de- signs can result in significant board space and cost savings. the designer can expect reli ability improvement over other available converters because of the sqe48 series? opti- mized thermal efficiency. applications ? telecommunications ? datacommunications ? wireless ? servers sqe48t converters features ? delivers up to 30a (99w) ? industry-standard quarter brick pinout ? extremely small footprint: 0.896? x 2.30? (2.06 in 2 ), 38% smaller than conventional quarter bricks ? higher current capability at elevated temperatures than most competitors' 30a quarter bricks ? on-board input differential lc-filter ? outputs available in 3.3, 2. 5, 1.8, 1.5, and 1.2v ? high efficiency ? no heatsink required ? start up into pre-biased output ? no minimum load required ? weight: 0.72 oz [20.6 g] ? meets basic insulation requirements of en60950 ? withstands 100 v input transient for 100 ms ? fixed frequency operation ? fully protected ? remote output sense ? positive or negative logic on/off option ? output voltage trim range: +10%/ ? 20% with industry- standard trim equations (except 1.2v output) ? high reliability: mtbf = tbd million hours, calculated per telcordia tr-332, method i case 1 ? ul 60950 recognized in us and canada and demko certified per iec/en 60950 (pending) ? meets conducted emissions requirements of fcc class b and en 55022 class b with external filter ? all materials meet ul94, v-0 flammability rating
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 2 of 33 electrical specifications (common to all versions) conditions: t a =25oc, airflow=300 lfm (1.5 m/s), vin=48 vdc, a ll output voltages, unless otherwise specified. parameter notes min typ max units absolute maximum ratings input voltage continuous 0 80 vdc operating ambient temperature -40 85 c storage temperature -55 125 c input characteristics operating input voltage range 36 48 75 vdc input under voltage lockout non-latching turn-on threshold 33 34 35 vdc turn-off threshold 31 32 33 vdc input voltage transient 100 ms 100 vdc isolation characteristics i/o isolation 2000 vdc isolation capacitance 160 pf isolation resistance 10 m ? feature characteristics switching frequency 415 khz output voltage trim range 1 industry-std. equations (3.3 - 1.5v) -20 +10 % use trim equation on page 4 (1.2v) -10 +10 % remote sense compensation 1 percent of v out ( nom ) +10 % output over-voltage protec tion non-latching 117 122 127 % over-temperature shutdown (pcb) non-latching 125 c auto-restart period applies to all protection features 100 ms turn-on time see figs. f, g and h 7 ms on/off control (positive logic) converter off -20 0.8 vdc converter on 2.4 20 vdc on/off control (negative logic) converter off 2.4 20 vdc converter on -20 0.8 vdc additional notes: 1. vout can be increased up to 10% via the sense leads or up to 10% via the trim function, however total output voltage trim fr om all sources should not exceed 10% of v out ( nom ), in order to insure specified operati on of over-voltage protection circuitry.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 3 of 33 operation input and output impedance these power converters have been designed to be stable with no external capacitors when used in low inductance in- put and output circuits. however, in many applications , the inductance associated with the distribution from the pow er source to the input of the converter can affect the stabilit y of the converter. the addi- tion of a 33f electrolytic capacitor with an esr < 1 ? across the input helps ensure stability of the converter. in many ap- plications, the user has to use decoupling capacitance at the load. the power converter will exhibit stable operation with external load capacitance up to 30,000f on 3.3 ? 1.2v out- puts. on/off (pin 2) the on/off pin is used to turn the power converter on or off remotely via a system signal. there are two remote con- trol options available, positive logic and negative logic and both are referenced to vin(-). typical connections are shown in fig. a. rload vin control input vin (+) vin (-) on/off vout (+) vout (-) trim sense (+) sense (-) (top view) converter semi q tm family fig. a: circuit configuration for on/off function. the positive logic version turns on when the on/off pin is at a logic high and turns off when at a logic low. the con- verter is on when the on/off pin is left open . the negative logic version turns on when the pin is at a logic low and turns off when the pin is at a logic high. the on/off pin can be hard wired directly to vin(-) to enable automatic power up of the co nverter without the need of an external control signal. on/off pin is internally pulled-up to 5v through a resistor. a mechanical switch, open collector transistor, or fet can be used to drive the input of the on/off pin. the device must be capable of sinking up to 0.2ma at a low level voltage of 0.8v. an external voltage source ( 20v maximum) may be connected directly to the on /off input, in which case it must be capable of sourcing or sinking up to 1ma depending on the signal polarity. see the start-up information section for system timing waveforms associated with use of the on/off pin. remote sense (pins 5 and 7) the remote sense feature of the converter compensates for voltage drops occurring between the output pins of the con- verter and the load. the sense(-) (pin 5) and sense(+) (pin 7) pins should be connecte d at the load or at the point where regulation is required (see fig. b). 100 10 rw rw rload vin vin (+) vin (-) on/off vout (+) vout (+) trim sense (+) sense (-) (top view) converter semi q tm family fig. b: remote sense circuit configuration. if remote sensing is not required, the sense(-) pin must be connected to the vout(-) pin (pin 4), and the sense(+) pin must be connected to the vout(+) pin (pin 8) to ensure the converter will regulate at t he specified output voltage. if these connections are not made, the converter will deliver an output voltage that is slightly higher than the specified value. because the sense leads carry minimal current, large traces on the end-user board are not required. however, sense traces should be located close to a ground plane to minimize system noise and insure optimum performance. when wiring discretely, twisted pair wires should be used to connect the sense lines to the load to reduce susceptibility to noise. the converter?s output over-vol tage protection (ovp) senses the voltage across vout(+) and vout(-), and not across the sense lines, so the resistance (and resulting voltage drop) between the output pins of the converter and the load should be minimized to prevent unwanted triggering of the ovp. when utilizing the remote sense feature, care must be taken not to exceed the maximum allowable output power capabil- ity of the converter, equal to the product of the nominal out- put voltage and the allowable ou tput current for the given conditions.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 4 of 33 when using remote sense, the output voltage at the con- verter can be increased by as much as 10% above the nominal rating in order to maintain the required voltage across the load. therefore, the designer must, if necessary, decrease the maximum current (originally obtained from the derating curves) by the same percentage to ensure the con- verter?s actual output power remains at or below the maxi- mum allowable output power. output voltage adjust /trim (pin 6) the output voltage can be adjusted up 10% or down 20% for vout 1.5v, and 10% for vout = 1.2v relative to the rated output voltage by the additi on of an externally connected resistor. for output voltage 3.3v, trim up to 10% is guaran- teed only at vin 40v, and it is marginal (8% to 10%) at vin = 36v. the trim pin should be left open if trimming is not being used. to minimize noise pickup, a 0.1f capacitor is con- nected internally between the trim and sense(-) pins. to increase the output voltage, refer to fig. c. a trim resis- tor, r t-incr , should be connected between the trim (pin 6) and sense(+) (pin 7), with a value of: 10.22 1.225 ? 626 ? )v 5.11(100 r nom o incr t [k : ] (3.3 ?1.5v) 7.2 ? 84.6 r incr t [k : ] (1.2v) where, incr t r required value of trim-up resistor k : ] nom o v nominal value of output voltage [v] 100 x v ) v (v ? nom - o nom - o req - o [%] req o v desired (trimmed) output voltage [v]. when trimming up, care must be taken not to exceed the converter?s maximum allowable output power. see previous section for a complete discussion of this requirement. rload vin vin (+) vin (-) on/off vout (+) vout (-) trim sense (+) sense (-) r t-incr (top view) converter semi q tm family fig. c: configuration for incr easing output voltage . to decrease the output voltage (fig. d), a trim resistor, r t-decr , should be connected between the trim (pin 6) and sense(-) (pin 5), with a value of: 10.22 ? 511 r decr t [k : ] (3.3 ? 1.5v) 15 ? 700 r decr t [k : ] (1.2v) where, decr t r required value of trim-down resistor [k : ] and ? is defined above. note: the above equations for calculation of trim resistor values match those typically used in conventional industry- standard quarter bricks. rload vin vin (+) vin (-) on/off vout (+) vout (-) trim sense (+) sense (-) r t-decr (top view) converter semi q tm family fig. d: configuration for decr easing output voltage. trimming/sensing beyond 110% of the rated output voltage is not an acceptable design practice, as this condition could cause unwanted triggering of the output over-voltage protec- tion (ovp) circuit. the designer should ensure that the dif- ference between the voltages ac ross the converter?s output pins and its sense pins does not exceed 10% of v out ( nom ), or: x nom - o sense sense out out 10% v )] ( v ) ( [v )] ( v ) ( [v d [v] this equation is applicable for any condition of output sens- ing and/or output trim.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 5 of 33 protection features input under-voltage lockout input under-voltage lockout is st andard with this converter. the converter will shut down when the input voltage drops below a pre-determined voltage. the input voltage must be typically 34 v for the converter to turn on. once the converter has been turned on, it will shut off when the input voltage drops typically below 32 v. this feature is beneficial in prev enting deep discharging of batter- ies used in telecom applications. output over-current protection (ocp) the converter is protected agains t over-current or short cir- cuit conditions. upon sensing an over-current condition, the converter will switch to cons tant current operation and thereby begin to reduce output voltage. when the output voltage drops below 60% of the nominal value of output volt- age, the converter will shut down (fig. x.15). once the converter ha s shut down, it will attempt to restart nominally every 100 ms with a typical 3-5% duty cycle (fig. x.16). the attempted rest art will continue indefinitely until the overload or short circ uit conditions are removed or the output voltage rises above 40-50% of its nominal value. output over-voltage protection (ovp) the converter will shut down if the output voltage across vout(+) (pin 8) and vout(-) (pin 4) exceeds the threshold of the ovp circuitry. the ovp circuitry contains its own refer- ence, independent of the output voltage regulation loop. once the converter ha s shut down, it will attempt to restart every 100 ms until the ovp condition is removed. over-temperature protection (otp) the converter will shut dow n under an ove r-temperature condition to protect itself fr om overheating caused by opera- tion outside the thermal derating curves, or operation in ab- normal conditions such as system fan failure. after the con- verter has cooled to a safe operating temperature, it will automatically restart. safety requirements the converters meet north american and international safety regulatory requirements per ul60950 and en60950 (pending). basic insulation is provided between input and output. to comply with safety agencies requirements, an input line fuse must be used external to the converter. the table be- low provides the recommended fuse rating for use with this family of products. output voltage fuse rating 3.3v 5 a 2.5v 4 a 1.8v , 1.5v 3 a 1.2v 2.5 a all sqe modules are ul approved for maximum fuse rating of 15a. to protect a group of modules with a single fuse, the rating can be increased from the recommended values above. electromagnetic compatibility (emc) emc requirements must be met at the end-product system level, as no specific standards dedicated to emc character- istics of board mounted component dc-dc converters exist. however, di/dt tests its conver ters to several system level standards, primary of which is the more stringent en55022, information technology equipment - radio disturbance char- acteristics - limits and methods of measurement. effective internal lc differentia l filter significantly reduces input reflected ripple current (fig. x.13), and improves emc. with the addition of a simple external filter, all versions of the sqe48 series of converters pass t he requirements of class b conducted emissions per en55022 and fcc, and meet at a minimum, class a radiated emissions per en 55022 and class b per fcc title 47cfr, part 15-j. please contact di/dt applications engineering for details of this testing. characterization general information the converter has been characterized for many operational aspects, to include thermal derating (maximum load current as a function of ambient temperature and airflow) for vertical and horizontal mounting, effici ency, start-up and shutdown parameters, output ripple and no ise, transient response to load step-change, overload and short circuit. the figures are numbered as fig. x.y, where x indicates the different output voltages, and y associates with specific plots (y = 1 for the vertical thermal derating, ?). for example, fig. x.1 will refer to the vertical t hermal derating for all the output voltages in general.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 6 of 33 the following pages contain specific plots or waveforms as- sociated with the converter. a dditional comments for specific data are provided below. test conditions all data presented were taken with the converter soldered to a test board, specifically a 0. 060? thick printed wiring board (pwb) with four layers. the top and bottom layers were not metalized. the two inner layers, comprising two-ounce cop- per, were used to provide traces for connectivity to the con- verter. the lack of metalization on the outer layers as well as the limited thermal connection ensured that heat transfer from the converter to the pwb was minimized. this provides a worst-case but consistent scenario for thermal derating pur- poses. all measurements requiring airflow were made in di/dt?s ver- tical and horizontal wind tunnel facilities using infrared (ir) thermography and thermocouples for thermometry. ensuring components on the converter do not exceed their ratings is important to maintaining high reliability. if one an- ticipates operating the converter at or close to the maximum loads specified in the derating curves, it is prudent to check actual operating temperatures in the application. thermo- graphic imaging is preferable; if this capability is not avail- able, then thermocouples may be used. di/dt recommends the use of awg #40 gauge thermocouples to ensure meas- urement accuracy. careful routing of the thermocouple leads will further minimize measurement error. refer to fig. e for optimum measuring thermocouple locations. fig. e: locations of the thermocouples for thermal testing. thermal derating load current vs. ambient temperature and airflow rates are given in fig. x.1 and fig. x.2. ambient temperature was var- ied between 25c and 85c, with airflow rates from 30 to 500 lfm (0.15 to 2.5m/s), for vertical and horizontal con- verter mounting. for each set of conditions, the maximum load current was defined as the lowest of: (i) the output current at which any fet junction temperature does not exceed a maximum spec ified temperature (120c) as indicated by the thermographic image, or (ii) the temperature of the transformer does not exceed 120c, or (iii) the nominal rating of the converter (30a on 3.3 ? 1.2v). during normal operation, derati ng curves with maximum fet temperature less or equal to 120c should not be exceeded. temperature at both thermocouple locations shown in fig. e should not exceed 120c in order to operate inside the derating curves. efficiency efficiency vs. load current plot is shown in fig. x.3 for ambi- ent temperature of 25oc, airf low rate of 300 lfm (1.5m/s), vertical converter mounting, and input voltages of 36v, 48v and 72v. also, a plot of efficiency vs. load current, as a func- tion of ambient temperature with vin = 48v, airflow rate of 200 lfm (1m/s) with vertical mounting is shown in fig. x.4. power dissipation fig. x.5 shows the power dissi pation vs. load current plot for ta = 25oc, airflow rate of 300 lfm (1.5m/s) with vertical mounting and input voltages of 36v, 48v and 72v. also, a plot of power dissipation vs. load current, as a function of ambient temperature with vin = 48v, airflow rate of 200 lfm (1m/s) with vertical mounting is shown in fig. x.6. start-up output voltage waveforms, during the turn-on transient using the on/off pin for full rated load currents (resistive load) are shown without and with external load capacitance in fig. x.7 and fig. x.8, respectively. ripple and noise fig. x.11 shows the output voltage ripple waveform, meas- ured at full rated load current with a 10f tantalum and 1f ceramic capacitor across the output. note that all output voltage waveforms are measured across a 1 f ceramic ca- pacitor. the input reflected ripple current waveforms are obtained using the test setup shown in fig x.12. the corresponding waveforms are shown in fig. x.13 and fig. x.14.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 7 of 33 start-up information (using negative on/off) scenario #1: initial start-up from bulk supply on/off function enabled, converte r started via application of v in . see figure f. time comments t 0 on/off pin is on; system front end power is toggled on, v in to converter begins to rise. t 1 v in crosses under-voltage lockout protection circuit threshold; converter enabled. t 2 converter begins to respond to turn-on command (con- verter turn-on delay). t 3 converter v out reaches 100% of nominal value. for this example, the total converter start-up time (t 3 - t 1 ) is typically 7 ms. scenario #2: initial start-up using on/off pin with v in previously powered, converter started via on/off pin. see figure g. time comments t 0 v input at nominal value. t 1 arbitrary time when on/off pin is enabled (converter enabled). t 2 end of converter turn-on delay. t 3 converter v out reaches 100% of nominal value. for this example, the total converter start-up time (t 3 - t 1 ) is typically 7 ms. scenario #3: turn-off and restart using on/off pin with v in previously powered, converter is disabled and then en- abled via on/off pin. see figure h. time comments t 0 v in and v out are at nominal values; on/off pin on. t 1 on/off pin arbitrarily disabled; converter output falls to zero; turn-on inhibit delay period (100 ms typical) is initiated, and on/off pin action is internally inhibited. t 2 on/off pin is externally re-enabled. if (t 2 - t 1 ) 100 ms , external action of on/off pin is locked out by start-up inhibit timer. if (t 2 - t 1 ) > 100 ms , on/off pin action is internally enabled. t 3 turn-on inhibit delay period ends. if on/off pin is on, converter begins turn-on; if off, converter awaits on/off pin on signal; see figure g. t 4 end of converter turn-on delay. t 5 converter v out reaches 100% of nominal value. for the condition, (t 2 - t 1 ) 100 ms , the total converter start-up time (t 5 - t 2 ) is typically 107 ms. for (t 2 - t 1 ) > 100 ms , start-up will be typically 7 ms after release of on/off pin. fig. f: start-up scenario #1. on/off state v out t 0 t 1 t 2 t 3 on off v in t fig. g: start-up scenario #2. on/off state off on v out t 0 t 2 t 1 t 5 v in t t 4 t 3 100 ms fig. h: start-up scenario #3. v in on/off state v out t t 0 t 1 t 2 t 3 on off
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 8 of 33 electrical specifications: sqe48t30033 (3.3 volt out ) conditions: t a =25oc, airflow=300 lfm (1.5 m/s), vin=48 vdc, vout=3.3 vdc unless otherwise specified. parameter notes min typ max units input characteristics maximum input current 30 adc, 3.3 vdc out @ 36 vdc in 3.1 adc input stand-by current vin = 48 v, converter disabled 3 madc input no load current (0 load on the output) vin = 48 v, converter enabled 37 madc input reflected-ripple current 25mhz bandwidth 8 ma pk-pk input voltage ripple rejection 120hz 91 db output characteristics output voltage set point (no load) 3.267 3.300 3.333 vdc output regulation over line 2 5 mv over load 2 5 mv output voltage range over line, load and temperature 2 3.250 3.350 vdc output ripple and noise - 25mhz bandwidth full load + 10 f tantalum + 1 f ceramic 30 50 mv pk-pk external load capacitance plus full load (resistive) 30,000 f output current range 0 30 adc current limit inception non-latching 33 36.5 40 adc peak short-circuit current non-latching. short=10m ? . 35 46 a rms short-circuit current non-latching 8 arms dynamic response load change 10a - 20a - 10a, di/dt = 0.1 a/ s co = 1 f ceramic (fig. 3.3v.9) 75 mv di/dt = 5 a/ s co = 470 f pos + 1 f ceramic (fig. 3.3v.10) 160 mv setting time to 1% 50 s efficiency 100% load 91 % 50% load 92.5 % additional notes: 2. -40oc to 85oc ambient temperature [c] 20 30 40 50 60 70 80 90 load current [adc] 0 5 10 15 20 25 30 35 500 lfm (2.5 m/s) 400 lfm (2.0 m/s) 300 lfm (1.5 m/s) 200 lfm (1.0 m/s) 100 lfm (0.5 m/s) 30 lfm (0.15 m/s) fig. 3.3v.1: available load current vs. ambient air temperature and airflow rates for sqe48t30033 converter with d height pins mounted vertically with air flowing from pin 3 to pin 1, mosfet temperature 120 c, vin = 48v. ambient temperature [c] 20 30 40 50 60 70 80 90 load current [adc] 0 5 10 15 20 25 30 35 500 lfm (2.5 m/s) 400 lfm (2.0 m/s) 300 lfm (1.5 m/s) 200 lfm (1.0 m/s) 100 lfm (0.5 m/s) 30 lfm (0.15 m/s) fig. 3.3v.2: available load current vs. ambient air temperature and airflow rates for sqe48t30033 converter with d height pins mounted horizontally with air flowing from pin 3 to pin 1, mosfet temperature 120 c, vin = 48v.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 9 of 33 sqe48t30033 (3.3 volt out ) load current [adc] 0 5 10 15 20 25 30 35 efficiency 0.70 0.75 0.80 0.85 0.90 0.95 1.00 72 v 48 v 36 v fig. 3.3v.3: efficiency vs. load current and input voltage for sqe48t30033 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 300 lfm (1.5m/s) and ta = 25 c. load current [adc] 0 5 10 15 20 25 30 35 p ower di ss i pa ti on [w] 0.00 2.00 4.00 6.00 8.00 10.00 12.00 72 v 48 v 36 v fig. 3.3v.5: power dissipation vs. load current and input volt- age for sqe48t30033 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 300 lfm (1.5m/s) and ta = 25 c. load current [adc] 0 5 10 15 20 25 30 35 efficiency 0.70 0.75 0.80 0.85 0.90 0.95 1.00 70 c 55 c 40 c fig. 3.3v.4: efficiency vs. load current and ambient tempera- ture for sqe48t30033 converter mounted vertically with vin = 48v and air flowing from pin 3 to pin 1 at a rate of 200 lfm (1.0m/s). load current [adc] 0 5 10 15 20 25 30 35 p ower di ss i pa ti on [w] 0.00 2.00 4.00 6.00 8.00 10.00 12.00 70 c 55 c 40 c fig. 3.3v.6: power dissipation vs. load current and ambient temperature for sqe48t30033 converter mounted vertically with vin = 48v and air flowing from pin 3 to pin 1 at a rate of 200 lfm (1.0m/s).
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 10 of 33 sqe48t30033 (3.3 volt out ) fig. 3.3v.7: turn-on transient at full rated load current (resis- tive) with no output capacitor at vin = 48v, triggered via on/off pin. top trace: on/off signal (5v/div.). bottom trace: output voltage (1v/div.). time scale: 2ms/div. fig. 3.3v.9: output voltage response to load current step- change (10a ? 20a ? 10a) at vin = 48v. top trace: output voltage (100mv/div.). bottom tr ace: load current (10a/div.). current slew rate: 0.1a/ s. co = 1 f ceramic. time scale: 0.2ms/div. fig. 3.3v.8: turn-on transient at full rated load current (resis- tive) plus 10,000 f at vin = 48v, triggered via on/off pin. top trace: on/off signal (5v/div. ). bottom trace: output volt- age (1v/div.). time scale: 2ms/div. fig. 3.3v.10: output voltage response to load current step- change (10a ? 20a ? 10a) at vin = 48v. top trace: output voltage (100mv/div.). bottom tr ace: load current (10a/div.). current slew rate: 5a/ s. co = 470 f pos + 1 f ceramic. time scale: 0.2ms/div.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 11 of 33 sqe48t30033 (3.3 volt out ) fig. 3.3v.11: output voltage ripple (20mv/div.) at full rated load current into a resistive load with co = 10 f tantalum + 1uf ceramic and vin = 48v. time scale: 1 s/div. fig. 3.3v.13: input reflected ripple current, i c (50ma/div.), measured at input terminals at full rated load current and vin = 48v. refer to fig. 3.3v.12 fo r test setup. time scale: 1 s/div. vout v source i s i c 1 f ceramic capacitor 10 h source inductance semi q tm family dc/dc converter 33 f esr <1 electrolytic capacitor ? fig. 3.3v.12: test set-up for measuring input reflected ripple currents, i c and i s . fig. 3.3v.14: input reflected ripple current, i s (10ma/div.), measured through 10 h at the source at full rated load current and vin = 48v. refer to fig. 3.3v.12 for test setup. time scale: 1 s/div.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 12 of 33 sqe48t30033 (3.3 volt out ) 10 20 30 40 4.0 iout [adc] vout [vdc] 0 0 3.0 2.0 1.0 fig. 3.3v.15: output voltage vs. load current showing current limit point and converter shutdown point. input voltage has al- most no effect on current limit characteristic. fig. 3.3v.16: load current (top trace, 20a/div., 20ms/div.) into a 10m ? short circuit during restart, at vin = 48v. bottom trace (20a/div., 1ms/div.) is an expans ion of the on-time portion of the top trace.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 13 of 33 electrical specifications: sqe48t30025 (2.5 volt out ) conditions: t a =25oc, airflow=300 lfm (1.5 m/s), vin=48 vdc, vout=2.5 vdc unless otherwise specified. parameter notes min typ max units input characteristics maximum input current 30 adc, 2.5 vdc out @ 36 vdc in 2.4 adc input stand-by current vin = 48v, converter disabled 3 madc input no load current (0 load on the output) vin = 48v, converter enabled 32 madc input reflected-ripple current 25mhz bandwidth 6 ma pk-pk input voltage ripple rejection 120hz 60 db output characteristics output voltage set point (no load) -40oc to 85oc 2.475 2.500 2.525 vdc output regulation over line 2 5 mv over load 2 5 mv output voltage range over line, load and temperature 2.462 2.538 vdc output ripple and noise - 25mhz bandwidth full load + 10 f tantalum + 1 f ceramic 30 50 mv pk-pk external load capacitance plus full load (resistive) 30,000 f output current range 0 30 adc current limit inception non-latching 33 36.5 40 adc peak short-circuit current non-latching. short=10m ? . 35 46 a rms short-circuit current non-latching 8 arms dynamic response load change 10a - 20a - 10a, di/dt = 0.1 a/ s co = 1 f ceramic (fig. 2.5v.9) 70 mv di/dt = 5 a/ s co = 470 f pos + 1 f ceramic (fig. 2.5v.10) 160 mv setting time to 1% 50 s efficiency 100% load 89.5 % 50% load 91.5 % ambient temperature [c] 20 30 40 50 60 70 80 90 load current [adc] 0 5 10 15 20 25 30 35 500 lfm (2.5 m/s) 400 lfm (2.0 m/s) 300 lfm (1.5 m/s) 200 lfm (1.0 m/s) 100 lfm (0.5 m/s) 30 lfm (0.15 m/s) fig. 2.5v.1: available load current vs. ambient air temperature and airflow rates for sqe48t30025 converter with d height pins mounted vertically with air flowing from pin 3 to pin 1, mosfet temperature 120 c, vin = 48v. ambient temperature [c] 20 30 40 50 60 70 80 90 load current [adc] 0 5 10 15 20 25 30 35 500 lfm (2.5 m/s) 400 lfm (2.0 m/s) 300 lfm (1.5 m/s) 200 lfm (1.0 m/s) 100 lfm (0.5 m/s) 30 lfm (0.15 m/s) fig. 2.5v.2: available load current vs. ambient air temperature and airflow rates for sqe48t30025 converter with d height pins mounted horizontally with air flowing from pin 3 to pin 1, mosfet temperature 120 c, vin = 48v.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 14 of 33 sqe48t30025 (2.5 volt out ) load current [adc] 0 5 10 15 20 25 30 35 efficiency 0.70 0.75 0.80 0.85 0.90 0.95 1.00 72 v 48 v 36 v fig. 2.5v.3: efficiency vs. load current and input voltage for sqe48t30025 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 300 lfm (1.5m/s) and ta = 25 c. load current [adc] 0 5 10 15 20 25 30 35 p ower di ss i pa ti on [w] 0.00 2.00 4.00 6.00 8.00 10.00 12.00 72 v 48 v 36 v fig. 2.5v.5: power dissipation vs. load current and input volt- age for sqe48t30025 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 300 lfm (1.5m/s) and ta = 25 c. load current [adc] 0 5 10 15 20 25 30 35 efficiency 0.70 0.75 0.80 0.85 0.90 0.95 1.00 70 c 55 c 40 c fig. 2.5v.4: efficiency vs. load current and ambient tempera- ture for sqe48t30025 converter mounted vertically with vin = 48v and air flowing from pin 3 to pin 1 at a rate of 200 lfm (1.0m/s). load current [adc] 0 5 10 15 20 25 30 35 p ower di ss i pa ti on [w] 0.00 2.00 4.00 6.00 8.00 10.00 12.00 70 c 55 c 40 c fig. 2.5v.6: power dissipation vs. load current and ambient temperature for sqe48t30025 converter mounted vertically with vin = 48v and air flowing from pin 3 to pin 1 at a rate of 200 lfm (1.0m/s).
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 15 of 33 sqe48t30025 (2.5 volt out ) fig. 2.5v.7: turn-on transient at full rated load current (resis- tive) with no output capacitor at vin = 48v, triggered via on/off pin. top trace: on/off signal (5v/div.). bottom trace: output voltage (1v/div.). time scale: 2ms/div. fig. 2.5v.9: output voltage response to load current step- change (10a ? 20a ? 10a) at vin = 48v. top trace: output voltage (100mv/div.). bottom tr ace: load current (10a/div.). current slew rate: 0.1a/ s. co = 1 f ceramic. time scale: 0.2ms/div. fig. 2.5v.8: turn-on transient at full rated load current (resis- tive) plus 10,000 f at vin = 48v, triggered via on/off pin. top trace: on/off signal (5v/div. ). bottom trace: output volt- age (1v/div.). time scale: 2ms/div. fig. 2.5v.10: output voltage response to load current step- change (10a ? 20a ? 10a) at vin = 48v. top trace: output voltage (100mv/div.). bottom tr ace: load current (10a/div.). current slew rate: 5a/ s. co = 470 f pos + 1 f ceramic. time scale: 0.2ms/div.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 16 of 33 sqe48t30025 (2.5 volt out ) fig. 2.5v.11: output voltage ripple (20mv/div.) at full rated load current into a resistive load with co = 10 f tantalum + 1uf ceramic and vin = 48v. time scale: 1 s/div. fig. 2.5v.13: input reflected ripple current, i c (50 ma/div.), measured at input terminals at full rated load current and vin = 48v. refer to fig. 2.5v.12 fo r test setup. time scale: 1 s/div. vout v source i s i c 1 f ceramic capacitor 10 h source inductance semi q tm family dc/dc converter 33 f esr <1 electrolytic capacitor ? fig. 2.5v.12: test set-up for measuring input reflected ripple currents, i c and i s . fig. 2.5v.14: input reflected ripple current, i s (10ma/div.), measured through 10 h at the source at full rated load current and vin = 48v. refer to fig. 2.5v.12 for test setup. time scale: 1 s/div.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 17 of 33 sqe48t30025 (2.5 volt out ) 10 20 30 40 4.0 iout [adc] vout [vdc] 0 0 3.0 2.0 1.0 fig. 2.5v.15: output voltage vs. load current showing current limit point and converter shutdown point. input voltage has al- most no effect on current limit characteristic. fig. 2.5v.16: load current (top trace, 20a/div., 20ms/div.) into a 10 m ? short circuit during restart, at vin = 48v. bottom trace (20a/div., 1ms/div.) is an expans ion of the on-time portion of the top trace.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 18 of 33 electrical specifications: sqe48t30018 (1.8 volt out ) conditions: t a =25oc, airflow=300 lfm (1.5 m/s), vin=48 vdc, vout=1.8 vdc unless otherwise specified. parameter notes min typ max units input characteristics maximum input current 30 adc, 1.8 vdc out @ 36 vdc in 1.7 adc input stand-by current vin = 48v, converter disabled 3 madc input no load current (0 load on the output) vin = 48v, converter enabled 28 madc input reflected-ripple current 25mhz bandwidth 6 ma pk-pk input voltage ripple rejection 120hz 70 db output characteristics output voltage set point (no load) -40oc to 85oc 1.782 1.800 1.818 vdc output regulation over line 2 4 mv over load 2 5 mv output voltage range over line, load and temperature 1.773 1.827 vdc output ripple and noise - 25mhz bandwidth full load + 10 f tantalum + 1 f ceramic 25 40 mv pk-pk external load capacitance plus full load (resistive) 30,000 f output current range 0 30 adc current limit inception non-latching 33 36.5 40 adc peak short-circuit current non-latching. short=10m ? . 35 46 a rms short-circuit current non-latching 8 arms dynamic response load change 10a - 20a - 10a, di/dt = 0.1 a/ s co = 1 f ceramic (fig. 1.8v.9) 50 mv di/dt = 5 a/ s co = 470 f pos + 1 f ceramic (fig. 1.8v.10) 150 mv setting time to 1% 50 s efficiency 100% load 87 % 50% load 89.5 % ambient temperature [c] 20 30 40 50 60 70 80 90 load current [adc] 0 5 10 15 20 25 30 35 500 lfm (2.5 m/s) 400 lfm (2.0 m/s) 300 lfm (1.5 m/s) 200 lfm (1.0 m/s) 100 lfm (0.5 m/s) 30 lfm (0.15 m/s) fig. 1.8v.1: available load current vs. ambient air temperature and airflow rates for sqe48t30018 converter with d height pins mounted vertically with air flowing from pin 3 to pin 1, mosfet temperature 120 c, vin = 48 v. ambient temperature [c] 20 30 40 50 60 70 80 90 load current [adc] 0 5 10 15 20 25 30 35 500 lfm (2.5 m/s) 400 lfm (2.0 m/s) 300 lfm (1.5 m/s) 200 lfm (1.0 m/s) 100 lfm (0.5 m/s) 30 lfm (0.15 m/s) fig. 1.8v.2: available load current vs. ambient air temperature and airflow rates for sqe48t30018 converter with d height pins mounted horizontally with air flowing from pin 3 to pin 1, mosfet temperature 120 c, vin = 48 v.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 19 of 33 sqe48t30018 (1.8 volt out ) load current [adc] 0 5 10 15 20 25 30 35 efficiency 0.65 0.70 0.75 0.80 0.85 0.90 0.95 72 v 48 v 36 v fig. 1.8v.3: efficiency vs. load current and input voltage for sqe48t30018 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 300 lfm (1.5m/s) and ta = 25 c. load current [adc] 0 5 10 15 20 25 30 35 p ower di ss i pa ti on [w] 0.00 2.00 4.00 6.00 8.00 10.00 12.00 72 v 48 v 36 v fig. 1.8v.5: power dissipation vs. load current and input volt- age for sqe48t30018 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 300 lfm (1.5m/s) and ta = 25 c. load current [adc] 0 5 10 15 20 25 30 35 efficiency 0.65 0.70 0.75 0.80 0.85 0.90 0.95 70 c 55 c 40 c fig. 1.8v.4: efficiency vs. load current and ambient tempera- ture for sqe48t30018 converter mounted vertically with vin = 48v and air flowing from pin 3 to pin 1 at a rate of 200 lfm (1.0m/s). load current [adc] 0 5 10 15 20 25 30 35 p ower di ss i pa ti on [w] 0.00 2.00 4.00 6.00 8.00 10.00 12.00 70 c 55 c 40 c fig. 1.8v.6: power dissipation vs. load current and ambient temperature for sqe48t30018 converter mounted vertically with vin = 48v and air flowing from pin 3 to pin 1 at a rate of 200 lfm (1.0m/s).
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 20 of 33 sqe48t30018 (1.8 volt out) fig. 1.8v.7: turn-on transient at full rated load current (resis- tive) with no output capacitor at vin = 48v, triggered via on/off pin. top trace: on/off signal (5v/div.). bottom trace: output voltage (1v/div.). time scale: 2ms/div. fig. 1.8v.9: output voltage response to load current step- change (10a ? 20a ? 10a) at vin = 48v. top trace: output voltage (100mv/div.). bottom tr ace: load current (10a/div.). current slew rate: 0.1a/ s. co = 1 f ceramic. time scale: 0.2ms/div. fig. 1.8v.8: turn-on transient at full rated load current (resis- tive) plus 10,000 f at vin = 48v, triggered via on/off pin. top trace: on/off signal (5v/div. ). bottom trace: output volt- age (1v/div.). time scale: 2ms/div. fig. 1.8v.10: output voltage response to load current step- change (10a ? 20a ? 10a) at vin = 48v. top trace: output voltage (100mv/div.). bottom tr ace: load current (10a/div.). current slew rate: 5a/ s. co = 470 f pos + 1 f ceramic. time scale: 0.2ms/div.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 21 of 33 sqe48t30018 (1.8 volt out) fig. 1.8v.11: output voltage ripple (20mv/div.) at full rated load current into a resistive load with co = 10 f tantalum + 1uf ceramic and vin = 48v. time scale: 1 s/div. fig. 1.8v.13: input reflected ripple current, i c (50ma/div.), measured at input terminals at full rated load current and vin = 48v. refer to fig. 1.8v.12 fo r test setup. time scale: 1 s/div. vout v source i s i c 1 f ceramic capacitor 10 h source inductance semi q tm family dc/dc converter 33 f esr <1 electrolytic capacitor ? fig. 1.8v.12: test set-up for measuring input reflected ripple currents, i c and i s . fig. 1.8v.14: input reflected ripple current, i s (10ma/div.), measured through 10 h at the source at full rated load current and vin = 48v. refer to fig. 1.8v.12 for test setup. time scale: 1 s/div.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 22 of 33 sqe48t30018 (1.8 volt out) 10 20 30 40 2.4 iout [adc] vout [vdc] 0 0 1.8 1.2 0.6 fig. 1.8v.15: output voltage vs. load current showing current limit point and converter shutdown point. input voltage has al- most no effect on current limit characteristic. fig. 1.8v.16: load current (top trace, 20a/div., 20ms/div.) into a 10 m ? short circuit during restart, at vin = 48v. bottom trace (20a/div., 1ms/div.) is an expans ion of the on-time portion of the top trace.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 23 of 33 electrical specifications: sqe48t30015 (1.5 volt out ) conditions: t a =25oc, airflow=300 lfm (1.5 m/s), vin=48 vdc, vout=1.5 vdc unless otherwise specified. parameter notes min typ max units input characteristics maximum input current 30 adc, 1.5 vdc out @ 36 vdc in 1.5 adc input stand-by current vin = 48v, converter disabled 3 madc input no load current (0 load on the output) vin = 48v, converter enabled 25 madc input reflected-ripple current 25mhz bandwidth 6 ma pk-pk input voltage ripple rejection 120hz 65 db output characteristics output voltage set point (no load) -40oc to 85oc 1.485 1.500 1.515 vdc output regulation over line 2 4 mv over load 2 4 mv output voltage range over line, load and temperature 1.477 1.523 vdc output ripple and noise - 25mhz bandwidth full load + 10 f tantalum + 1 f ceramic 20 30 mv pk-pk external load capacitance plus full load (resistive) 30,000 f output current range 0 30 adc current limit inception non-latching 33 36.5 40 adc peak short-circuit current non-latching. short=10m ? . 35 46 a rms short-circuit current non-latching 8 arms dynamic response load change 10a - 20a - 10a, di/dt = 0.1 a/ s co = 1 f ceramic (fig. 1.5v.9) 40 mv di/dt = 5 a/ s co = 470 f pos + 1 f ceramic(fig. 1.5v.10) 140 mv setting time to 1% 50 s efficiency 100% load 86 % 50% load 88.5 % ambient temperature [c] 20 30 40 50 60 70 80 90 load current [adc] 0 5 10 15 20 25 30 35 500 lfm (2.5 m/s) 400 lfm (2.0 m/s) 300 lfm (1.5 m/s) 200 lfm (1.0 m/s) 100 lfm (0.5 m/s) 30 lfm (0.15 m/s) fig. 1.5v.1: available load current vs. ambient air temperature and airflow rates for sqe48t30015 converter with d height pins mounted vertically with air flowing from pin 3 to pin 1, mosfet temperature 120 c, vin = 48v. ambient temperature [c] 20 30 40 50 60 70 80 90 load current [adc] 0 5 10 15 20 25 30 35 500 lfm (2.5 m/s) 400 lfm (2.0 m/s) 300 lfm (1.5 m/s) 200 lfm (1.0 m/s) 100 lfm (0.5 m/s) 30 lfm (0.15 m/s) fig. 1.5v.2: available load current vs. ambient air temperature and airflow rates for sqe48t30015 converter with d height pins mounted horizontally with air flowing from pin 3 to pin 1, mosfet temperature 120 c, vin = 48v.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 24 of 33 sqe48t30015 (1.5 volt out ) load current [adc] 0 5 10 15 20 25 30 35 efficiency 0.65 0.70 0.75 0.80 0.85 0.90 0.95 72 v 48 v 36 v fig. 1.5v.3: efficiency vs. load current and input voltage for sqe48t30015 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 300 lfm (1.5m/s) and ta = 25 c. load current [adc] 0 5 10 15 20 25 30 35 p ower di ss i pa ti on [w] 0.00 2.00 4.00 6.00 8.00 10.00 72 v 48 v 36 v fig. 1.5v.5: power dissipation vs. load current and input volt- age for sqe48t30015 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 300 lfm (1.5m/s) and ta = 25 c. load current [adc] 0 5 10 15 20 25 30 35 efficiency 0.65 0.70 0.75 0.80 0.85 0.90 0.95 70 c 55 c 40 c fig. 1.5v.4: efficiency vs. load current and ambient tempera- ture for sqe48t30015 converter mounted vertically with vin = 48v and air flowing from pin 3 to pin 1 at a rate of 200 lfm (1.0m/s). load current [adc] 0 5 10 15 20 25 30 35 p ower di ss i pa ti on [w] 0.00 2.00 4.00 6.00 8.00 10.00 70 c 55 c 40 c fig. 1.5v.6: power dissipation vs. load current and ambient temperature for sqe48t30015 converter mounted vertically with vin = 48v and air flowing from pin 3 to pin 1 at a rate of 200 lfm (1.0m/s).
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 25 of 33 sqe48t30015 (1.5 volt out) fig. 1.5v.7: turn-on transient at full rated load current (resis- tive) with no output capacitor at vin = 48v, triggered via on/off pin. top trace: on/off signal (5v/div.). bottom trace: output voltage (1v/div.). time scale: 2ms/div. fig. 1.5v.9: output voltage response to load current step- change (10a ? 20a ? 10a) at vin = 48v. top trace: output voltage (100mv/div.). bottom tr ace: load current (10a/div.). current slew rate: 0.1a/ s. co = 1 f ceramic. time scale: 0.2ms/div. fig. 1.5v.8: turn-on transient at full rated load current (resis- tive) plus 10,000 f at vin = 48v, triggered via on/off pin. top trace: on/off signal (5v/div. ). bottom trace: output volt- age (1v/div.). time scale: 2ms/div. fig. 1.5v.10: output voltage response to load current step- change (10a ? 20a ? 10a) at vin = 48v. top trace: output voltage (100mv/div.). bottom tr ace: load current (10a/div.). current slew rate: 5a/ s. co = 470 f pos + 1 f ceramic. time scale: 0.2ms/div.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 26 of 33 sqe48t30015 (1.5 volt out) fig. 1.5v.11: output voltage ripple (20mv/div.) at full rated load current into a resistive load with co = 10 f tantalum + 1uf ceramic and vin = 48v. time scale: 1 s/div. fig. 1.5v.13: input reflected ripple current, i c (50ma/div.), measured at input terminals at full rated load current and vin = 48v. refer to fig. 1.5v.12 fo r test setup. time scale: 1 s/div. vout v source i s i c 1 f ceramic capacitor 10 h source inductance semi q tm family dc/dc converter 33 f esr <1 electrolytic capacitor ? fig. 1.5v.12: test set-up for measuring input reflected ripple currents, i c and i s . fig. 1.5v.14: input reflected ripple current, i s (10ma/div.), measured through 10 h at the source at full rated load current and vin = 48v. refer to fig 1.5v.12 for test setup. time scale: 1 s/div.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 27 of 33 sqe48t30015 (1.5 volt out) 10 20 30 40 2.0 iout [adc] vout [vdc] 0 0 1.5 1.0 0.5 fig. 1.5v.15: output voltage vs. load current showing current limit point and converter shutdown point. input voltage has al- most no effect on current limit characteristic. fig. 1.5v.16: load current (top trace, 20a/div., 20ms/div.) into a 10 m ? short circuit during restart, at vin = 48v. bottom trace (20a/div., 1ms/div.) is an expans ion of the on-time portion of the top trace.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 28 of 33 electrical specifications: sqe48t30012 (1.2 volt out ) conditions: t a =25oc, airflow=300 lfm (1.5 m/s), vin=48 vdc, vout=1.2 vdc unless otherwise specified. parameter notes min typ max units input characteristics maximum input current 30 adc, 1.2 vdc out @ 36 vdc in 1.2 adc input stand-by current vin = 48v, converter disabled 3 madc input no load current (0 load on the output) vin = 48v, converter enabled 23 madc input reflected-ripple current 25mhz bandwidth 6 ma pk-pk input voltage ripple rejection 120hz 65 db output characteristics output voltage set point (no load) -40oc to 85oc 1.188 1.200 1.212 vdc output regulation over line 1 3 mv over load 1 3 mv output voltage range over line, load and temperature 1.182 1.218 vdc output ripple and noise - 25mhz bandwidth full load + 10 f tantalum + 1 f ceramic 20 30 mv pk-pk external load capacitance plus full load (resistive) 30,000 f output current range 0 30 adc current limit inception non-latching 33 36.5 40 adc peak short-circuit current non-latching. short=10m ? . 35 46 a rms short-circuit current non-latching 8 arms dynamic response load change 10a - 20a - 10a, di/dt = 0.1 a/ s co = 1 f ceramic (fig. 1.2v.9) 40 mv di/dt = 5 a/ s co = 470 f pos + 1 f ceramic (fig. 1.2v.10) 130 mv setting time to 1% 50 s efficiency 100% load 84 % 50% load 86.5 % ambient temperature [c] 20 30 40 50 60 70 80 90 load current [adc] 0 5 10 15 20 25 30 35 500 lfm (2.5 m/s) 400 lfm (2.0 m/s) 300 lfm (1.5 m/s) 200 lfm (1.0 m/s) 100 lfm (0.5 m/s) 30 lfm (0.15 m/s) fig. 1.2v.1: available load current vs. ambient air temperature and airflow rates for sqe48t30012 converter with d height pins mounted vertically with air flowing from pin 3 to pin 1, mosfet temperature 120 c, vin = 48v. ambient temperature [c] 20 30 40 50 60 70 80 90 load current [adc] 0 5 10 15 20 25 30 35 500 lfm (2.5 m/s) 400 lfm (2.0 m/s) 300 lfm (1.5 m/s) 200 lfm (1.0 m/s) 100 lfm (0.5 m/s) 30 lfm (0.15 m/s) fig. 1.2v.2: available load current vs. ambient air temperature and airflow rates for sqe48t30012 converter with d height pins mounted horizontally with air flowing from pin 3 to pin 1, mosfet temperature 120 c, vin = 48v.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 29 of 33 sqe48t30012 (1.2 volt out ) load current [adc] 0 5 10 15 20 25 30 35 efficiency 0.65 0.70 0.75 0.80 0.85 0.90 0.95 72 v 48 v 36 v fig. 1.2v.3: efficiency vs. load current and input voltage for sqe48t30012 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 300 lfm (1.5m/s) and ta = 25 c. load current [adc] 0 5 10 15 20 25 30 35 p ower di ss i pa ti on [w] 0.00 2.00 4.00 6.00 8.00 10.00 72 v 48 v 36 v fig. 1.2v.5: power dissipation vs. load current and input volt- age for sqe48t30012 converter mounted vertically with air flowing from pin 3 to pin 1 at a rate of 300 lfm (1.5m/s) and ta = 25 c. load current [adc] 0 5 10 15 20 25 30 35 efficiency 0.65 0.70 0.75 0.80 0.85 0.90 0.95 70 c 55 c 40 c fig. 1.2v.4: efficiency vs. load current and ambient tempera- ture for sqe48t30012 converter mounted vertically with vin = 48v and air flowing from pin 3 to pin 1 at a rate of 200 lfm (1.0m/s). load current [adc] 0 5 10 15 20 25 30 35 p ower di ss i pa ti on [w] 0.00 2.00 4.00 6.00 8.00 10.00 70 c 55 c 40 c fig. 1.2v.6: power dissipation vs. load current and ambient temperature for sqe48t30012 converter mounted vertically with vin = 48v and air flowing from pin 3 to pin 1 at a rate of 200 lfm (1.0m/s).
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 30 of 33 sqe48t30012 (1.2 volt out ) fig. 1.2v.7: turn-on transient at full rated load current (resis- tive) with no output capacitor at vin = 48v, triggered via on/off pin. top trace: on/off signal (5v/div.). bottom trace: output voltage (1v/div.). time scale: 2ms/div. fig. 1.2v.9: output voltage response to load current step- change (10a ? 20a ? 10a) at vin = 48v. top trace: output voltage (100mv/div.). bottom tr ace: load current (10a/div.). current slew rate: 0.1a/ s. co = 1 f ceramic. time scale: 0.2ms/div. fig. 1.2v.8: turn-on transient at full rated load current (resis- tive) plus 10,000 f at vin = 48v, triggered via on/off pin. top trace: on/off signal (5v/div. ). bottom trace: output volt- age (1v/div.). time scale: 2ms/div. fig. 1.2v.10: output voltage response to load current step- change (10a ? 20a ? 10a) at vin = 48v. top trace: output voltage (100mv/div.). bottom tr ace: load current (10a/div.). current slew rate: 5a/ s. co = 470 f pos + 1 f ceramic. time scale: 0.2ms/div.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 31 of 33 sqe48t30012 (1.2 volt out ) fig. 1.2v.11: output voltage ripple (20mv/div.) at full rated load current into a resistive load with co = 10 f tantalum + 1uf ceramic and vin = 48v. time scale: 1 s/div. fig. 1.2v.13: input reflected ripple current, i c (50 ma/div.), measured at input terminals at full rated load current and vin = 48v. refer to fig. 1.2v.12 fo r test setup. time scale: 1 s/div. vout v source i s i c 1 f ceramic capacitor 10 h source inductance semi q tm family dc/dc converter 33 f esr <1 electrolytic capacitor ? fig. 1.2v.12: test set-up for measuring input reflected ripple currents, i c and i s . fig. 1.2v.14: input reflected ripple current, i s (10ma/div.), measured through 10 h at the source at full rated load current and vin = 48v. refer to fig. 1.2v.12 for test setup. time scale: 1 s/div.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 32 of 33 sqe48t30012 (1.2 volt out ) 10 20 30 40 1.6 iout [adc] vout [vdc] 0 0 1.2 0.8 0.4 fig. 1.2v.15: output voltage vs. load current showing current limit point and converter shutdown point. input voltage has al- most no effect on current limit characteristic. fig. 1.2v.16: load current (top trace, 20a/div., 20ms/div.) into a 10 m ? short circuit during restart, at vin = 48v. bottom trace (20a/div., 1ms/div.) is an expans ion of the on-time portion of the top trace.
sqe48 series - 30a data sheet sqe48t30 family ds rev 1 07-28-04 usa toll free 866 wow-didt page 33 of 33 physical information side view top view 1 2 3 7 8 6 5 4 sqe48t pinout (through-hole) converter part numbering scheme product series input voltage mounting scheme rated load current output voltage on/off logic maximum height [ht] pin length [pl] special features sqe 48 t 30 033 - n d b 0 one-eighth brick format 36-75 v t ? through-hole 30a (1.2 ? 3.3v) 012 ? 1.2v 015 ? 1.5v 018 ? 1.8v 025 ? 2.5v 033 ? 3.3v n ? negative p ? positive through hole d ? 0.381? through hole a ? 0.188? b ? 0.145? c ? 0.110? 0 ? std the example above describes p/n sqe48t30033-ndb0: 36-75v input, through-hole mounting, 30a @ 3.3v output, negative on/off logic , a maximum height of 0.381?, and a through the board pin length of 0.145?. please consult factory regarding av ailability of a specific version. for more information please contact di/dt , a power-one company 1822 aston avenue ?? carlsbad, ca ?? 92008 ?? usa usa toll free 866-wow-didt (969-3438) www.didt.com ?? support@didt.com the information and specifications c ontained in this data sheet are believed to be accurate and reliable at the time of publica tion. however, power-one, inc. assumes no responsibility for its use or for any infringements of patents or othe r rights of third parties, which may result from its use. no license is granted by i mplication or otherwise under any patent or patent rights of power-one, inc. specifications are subject to change wit hout notice. ?copyright power-one, inc. 2004 ht (max. height) cl (min. clearance) height option +0.000 [+0.00] -0.038 [- 0.97] +0.016 [+0.41] -0.000 [- 0.00] d 0.381 [9.68] 0.008 [0.3] pl pin length pin option 0.005 [0.13] a 0.188 [4.77] b 0.145 [3.68] c 0.110 [2.79] pad/pin connections pad/pin # function 1 vin (+) 2 on/off 3 vin (-) 4 vout (-) 5 sense(-) 6 trim 7 sense(+) 8 vout (+) sqe48t platform notes ? all dimensions are in inches [mm] ? pins 1-3 and 5-7 are ? 0.040? [1.02] with ? 0.078? [1.98] shoulder ? pins 4 and 8 are ? 0.062? [1.57] without shoulder ? pin material: brass ? pin finish: tin/lead over nickel ? converter weight: 0.72 oz [20.6 g]

▲Up To Search▲

Price & Availability of SQE48T30033-NDC0

	To Download SQE48T30033-NDC0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .